Author - silicone

How to print HD super soft matte silicone effect?

Tips printing process for soft matte effect printing Preparation: Mesh&Squeegee: 120(48T) Mesh number; 65-75 degree Squeegee.: Pigments added ratio: For white and fluorescent colors 20%, other colors 10%Catalyst mixing ratio:2% Silicone thinner XG-128A adding ratio:0-20%    Heating Temp and time: Flash cure temp: 100℃- 120℃ for 6-10 seconds, Drying temp: 120℃- 140℃ for about 2 -3 minutes. Silicone ink printing tips: 1. HD silicone XG-866A/866AH for under coating  and high density printing for...

How to Screen Print HD glossy golden silicone Effect?

Tips for golden silicone ink printing Preparation: Mesh&Squeegee: 120(48T) Mesh number; 65-75 degree Squeegee.Pigments added ratio: For white and fluorescent colors 20%, other colors 10%, glitter powders 10%.Catalyst mixing ratio: 2% slow dry XG-866B-1 and fast dry XG-866B-2 can mix together for use.Silicone thinner XG-128A adding ratio: 0-20% Silicone thinner is not necessary for hand printingHeating Temp and time: Flash cure temp:100℃- 120℃ for 6-10 seconds, Drying temp: 120℃- 140℃ for 2-3...

How to print supper smooth glossy silicone effect?

Key points for HD Glossy Silicone Ink Screen Printing 1st To make a thick screen  2nd For the hairy fabric, to heat press by heat press machine or iron after first-time silicone printing for smooth effect. Silicone ink is sticky when lifting up the screen and heated all fabric hairy will stand up, if heat presses then all fabric hairy will lie flat...

How to 3D Emboss Silicone Screen Printing for Sportswear fabric?

Mesh number 80-120 (32-48T) Embossing printing silicone ink and catalyst Mixing Ratio: Embossing silicone ink  XG-360KY-55:  50G Embossing silicone catalyst XG-360BH:   5G   (mixing ratio 10%) Silicone thinner  XG-128AH: not necessary Print mixing silicone ink on the backside of the fabric Machine temp set temp : Upper mold 180 degree Bottom mold 120-150 degree Can stick a thin fabric on the printing fabric backside   (depends on  design ) Heating time 8-15 seconds   (depends...

How to print anti-slip silicone ink on a gloves printing machine?

Anti-slip gloves printing silicone ink printing tips: Preparation: Mesh: 30-60(12T-24T) to make a thick screen by emulsion. Better to use Hollow aluminum.Pigments added ratio:2-4%Catalyst mixing ratio:2% Thinner XG-128AH adding ratio:0-10%    thinner is not necessary Heating Temp and time: 120℃ -150℃ for 6-12 seconds, Heating time depends on drying temp. Silicone ink mixing tips: Printing silicone       XG-15A        60G Catalyst               XG-15B       1.2G  (2%) Pigment              XG-           1.2-2.4G  (2-4%) If need color effect To print by thick...

How to dip soft taps for a good sharp and supper soft smooth matte silicone effect?

Dipping tips for hard hand feel and dipping silicone ink and soft smooth dipping silicone ink: 1st  Dip hard hand feel silicone Clear layer 1 time The Hard hand feel silicone        XG-60S   100G The Hard hand feel silicone catalyst  XG-60S-ZB    10G  10% (10G silicone to mix with 1G catalyst) No need to mix with silicone thinner To dip one time and wait about 40-70 minutes...

How to dip fully transparent silicone on ropes cords shoelaces?

Transparent and fluorescent color effect dipping cords ropes shoelace dip process: Fully transparent dipping silicone dip 1 time: Dipping silicone    XG-20S-3    60G Silicone catalyst   XG-ZB-1      6G  10% Silicone thinner    XG-128AH     36-48G 60-80% Vacuum first for better smooth Shaking and removing excess silicone ink after dipping Color dipping silicone dip 1 time if needed color effect Dipping silicone    XG-20S-3    60G Silicone pigments   XG-series    3G  5% Silicone catalyst   XG-ZB-1      6G  10% Silicone thinner    XG-128AH     36-48G  60-80% Vacuum first...

How to print PU Water Based Nylon Ink on knitting shoe upper?

First ,Preparation: Mesh&Squeegee: 120-150(48T-60T) Mesh number; 65-70 degree Squeegee. Fixer mixing ratio:2%Flash and curing temp: 80℃- 100℃ or by room temp Second , printing process: 1 HD PU water based nylon Ink print for 6-12 layers : HD PU water based nylon Ink     XGS-806          300 G Fixer                            XGS-339           6G  2%    Flash by 80℃- 100℃ or by room temp 2 Red color smooth PU water based nylon Ink print for 3-4 layers Red PU water...

How to print machine printing silicone ink on an Oval printing machine?

Printing Tips for Machine Printing Silicone Ink Preparation: Mesh&Squeegee: 120(48T) Mesh number ;Squeegee 65-75 degrees Squeegee sharp and flat.: Pigments added ratio: For white and fluorescent colors 20%, other colors 10%Catalyst mixing ratio:2% slow dry XG-866B-1for small printing size, fast dry XG-866B-2 for large printing size and first under printing screen. Slow dry and fast dry catalysts can mix together for...

Hello~