Check out our Latest News!
Key points for HD Glossy Silicone Ink Screen Printing 1st To make a thick screen 2nd For the hairy fabric, to heat press by heat press machine or iron after first-time silicone printing for smooth effect. Silicone ink is sticky when lifting up the screen and heated all fabric hairy will stand up, if heat presses then all fabric hairy will lie flat...
Mesh number 80-120 (32-48T) Embossing printing silicone ink and catalyst Mixing Ratio: Embossing silicone ink XG-360KY-55: 50G Embossing silicone catalyst XG-360BH: 5G （mixing ratio 10%） Silicone thinner XG-128AH: not necessary Print mixing silicone ink on the backside of the fabric Machine temp set temp : Upper mold 180 degree Bottom mold 120-150 degree Can stick a thin fabric on the printing fabric backside (depends on design ) Heating time 8-15 seconds (depends...
Anti-slip gloves printing silicone ink printing tips: Preparation: Mesh: 30-60(12T-24T) to make a thick screen by emulsion. Better to use Hollow aluminum.Pigments added ratio:2-4%Catalyst mixing ratio:2% Thinner XG-128AH adding ratio:0-10% thinner is not necessary Heating Temp and time: 120℃ -150℃ for 6-12 seconds, Heating time depends on drying temp. Silicone ink mixing tips: Printing silicone XG-15A 60G Catalyst XG-15B 1.2G (2%) Pigment XG- 1.2-2.4G (2-4%) If need color effect To print by thick...
Dipping tips for hard hand feel and dipping silicone ink and soft smooth dipping silicone ink: 1st Dip hard hand feel silicone Clear layer 1 time The Hard hand feel silicone XG-60S 100G The Hard hand feel silicone catalyst XG-60S-ZB 10G 10% (10G silicone to mix with 1G catalyst) No need to mix with silicone thinner To dip one time and wait about 40-70 minutes...
Transparent and fluorescent color effect dipping cords ropes shoelace dip process: Fully transparent dipping silicone dip 1 time: Dipping silicone XG-20S-3 60G Silicone catalyst XG-ZB-1 6G 10% Silicone thinner XG-128AH 36-48G 60-80% Vacuum first for better smooth Shaking and removing excess silicone ink after dipping Color dipping silicone dip 1 time if needed color effect Dipping silicone XG-20S-3 60G Silicone pigments XG-series 3G 5% Silicone catalyst XG-ZB-1 6G 10% Silicone thinner XG-128AH 36-48G 60-80% Vacuum first...
Textile Cords dipping Silicone Ink, The Supper Transparent dipping ink for shoelaces silicone tipping. Supper transparent dipping ink Fluorescent colors Silicone Ink for Ropes dipping Ropes dipping Silicone Ink XG Silicone Ink Cords dipping Luminescent silicone ink XG rope tipping silicone ink
First ,Preparation: Mesh&Squeegee: 120-150(48T-60T) Mesh number; 65-70 degree Squeegee. Fixer mixing ratio:2%Flash and curing temp: 80℃- 100℃ or by room temp Second , printing process: 1 HD PU water based nylon Ink print for 6-12 layers : HD PU water based nylon Ink XGS-806 300 G Fixer XGS-339 6G 2% Flash by 80℃- 100℃ or by room temp 2 Red color smooth PU water based nylon Ink print for 3-4 layers Red PU water...
Printing Tips for Machine Printing Silicone Ink Preparation: Mesh&Squeegee: 120(48T) Mesh number ;Squeegee 65-75 degrees Squeegee sharp and flat.: Pigments added ratio: For white and fluorescent colors 20%, other colors 10%Catalyst mixing ratio:2% slow dry XG-866B-1for small printing size, fast dry XG-866B-2 for large printing size and first under printing screen. Slow dry and fast dry catalysts can mix together for...
Preparation: Mesh: 180-300(70T-120T) Mesh number ;Squeegee:70-75 degree Flat SqueegeeFixer mixing ratio: 9103 Fixer mixing ratio 1-2% (If under coating clear SND-110 to mix fixer SND-110B 10%)Reducer :0-20%Flash by air or heating by 40-60℃Cure by waiting over 12 hours or heat by 40-60℃ for 30 minutes Solvent based ink printing process: 1.Under coating Clear SND-110AB print for 1 time: Under Coating Solvent Based Clear ...
Shoelace Tipping ink, Tipping silicone dipping process TDS of XG shoelace dipping silicone 1st Dipping silicone Clear layer 1 time Dipping silicone XG-20S-1 100G Fast dry silicone catalyst XG-KB-1 10G 10% (10G silicone to mix with 1G catalyst) Silicone thinner XG-128AH 120-150G 120-150% (10G silicone to mix with 12-15G thinner) To dip one time and wait about 40-70 minutes to get the ink layer surface...
